LMCSS CONTRACT PARAMETER FOR AAA30085AAF

　　Installation Parameters (2-3-1)

　　Top floor _________----Enter top landing minus one

　　Bottom floor _________Lowest landing is always 0

　　Country AJG _________Enter 0 for NAA, 1=JAPAN,2=GERMANY

　　Enable ADO__________Set to a 1 to enable Advanced Door Open feature

　　DBSS parity OE____1_____Drive Dependent Prity Flag –

　　set to a 1

　　Car non start _____30__Length of time for a normal high speed run without seeing a DZ signal

　　Track err% NOR ______15______Set to 15 after Final adjustment

　　NTSD cutoff% _________ set to 60 initially ,reset during adjusting of NTSD

　　Upper Access Flr _______ Enter landing number of top access floor

　　ED car ID____0_____ set to elevator number in group for enhanced diagnostics,REM

　　Elev type _______enter 8 for GEM,9 for MVS & HVS

　　Dual ANSI SC brd _____0____

　　LSP Type ____0_____Can.B44:Enter “1” with rope grabber

　　Enter “2” with Gov. Trip soleniods Enter 0 for NAA operation

　　Ena CEN_HONGKONG _____0____ENTER 1 for CEN-HongKong controller

　　Ena pvt check ____2____

　　Track. Debnce cyc ____8____

　　MCSS to OCSS ICD _______0___ Enter 1 for B44 & DLF operation on NAA controllers after 8/1/97

　　Ena B44 DLF _______0____Enter 1 for B44 & DLF operation on NAA controllers after 8/1/97

　　ADV PTR option ____0___ HVS=10

　Install2 (2-3-2)

　　Ena Dir Lim NY __0_____N=0,Y=1,Enable software direction limit

　　Rotate DIR NY______0___N=0,Y=1,Reverse PVT direction information from DBSS

　　Adv PTR Holdoff ___0_____Advanced prepare to run holdoff (100 ms),10-forgeared,0-for gearless

　　Wrt Prot Opt NY ____0____N=0,Y=1,Enable running the elevator with the write protect switch enable

　　Enable prejerk Vel_____0______ Not used on VF Drive

　　Prejerk Ramp Cyc ____7____

　　-----------------Dlt ____3______

　　DOOR COMM TYPE ____0_____DCSS(pnt –pnt)=0,Multidrop=1,Multidrop W/HPLIM=2注意HPLIM设为0

　　REM Enable _____0_____W/0 REM=0,W/REM=255(ENABLE/DISABLE)

　　REM Event Buffer _________0___ W/0 REM=0 W/REM=255(enable/unable)

　　REM Tim Event Ln ___5______ # of 100msec cycles

　　REM BAUD Rate _____48____ 4800 baud (only)

　　REM Msg Sumcheck _____255___ W/0 REM =0,W/REM=255(enable/disable)

　　Profile generator(2-3-3)

　　Velocity normal __________ Enter contract speed in mm/s

　　Accelera Normal _____ Enter 600 for all GEM & MVS 5035 duty :1000 for all other MVS/HVS duties

　　Jerk Normal ___1560____

　　*

　　Velocity Inspect _____350____

　　*Accelera Inspect ___600___

　　*Velocity Learn ____150____

　　*Accelera Learn __600____

　　Velocity Relevel __60____

*Accelera Relevel _____300____

　　Velocity Recover _250_

　　*Accelera Recover ___600____

　　*Velocity Slow ____150____

　　Velocity Reinit _____900___

　　Accelera Reinit ________Enter 600 for all GEM & MVS 5035 duties 1200 for all other MVS/HVS duties

　　Accelera NTSD ___________Enter 800 for GEM & MVS 5035 duties 1200 for all other MVS/HVS duties

　　NTSD Comp Distance ________Enter 200 for 1016 mm/s contract speed

　　Jerk timed __0_____

　　Velocity reduced ____700_____

　　Accelera reduced __600______

　　Jerk reduced ___600_____

　　Velocity profile 2 _1000____

　　Accel profile 2 _____600______

　　Jerk profile 2 ____1560_____

　　Velocity profile 3 __1000______

　　Accel profile 3 __600____

　　Jerk profile 3 ___1560____

　　Velocity test __1000_____

　　Acceleration test _600____

　　Jerk test ____1560______

　　Velocity zero ___1____

　　JPSDO type ____0______

　　Velocity JPSDO_____0____

　　*Gain fixed posct ______25_____

　　*Delta TC ___240____Minimum setting for VF drive

　　Decel/accel % _____100______

　　Destination Lead _____0____

　　Destination Lag______0______

　　Level tolerance __3_____

　　Zero speed time ____500____

　　BKL to Mov time ___0__

　　EOR PTR time ___0____Without Brake swicth,set to 5

　　Relevel delay_____50_____

　　CAB HEIGHT _2500____Set distance in mm to stop car with cross-head level with tp access ldg.level.

　　Bot ACCESS LEN ___2500____Set distance in mm,when set to 65535,bottom access length is set to full length of hoistway.

　　Position displmt ____0______

　　1LS/2LS tolerance _____300____